Search Results

Over the last ten years there has been a steady growth in the market share of light-duty diesel engines, especially in Europe. At the same time, a general trend in petrol engine development has been seen, in which normal aspirated engines are being replaced by downsized turbocharged engines. Therefore, NVH engineers have to deal with new challenges. Turbochargers produce an aerodynamic noise in the frequency range above 1000Hz, which might influence the exterior and interior noise level. As a result, the additional requirement for acoustical components to reduce this flow noise is going to pose an increasing challenge for air intake system suppliers. This paper describes a new design of well-known wide band silencer first mentioned by A. Selamet, N.S.Dickey and J.M.Novak [1,2]. The silencer works according to the interference principle. The sound is guided into two or more parallel pipes of different lengths.

The HD Radio™ system is a key element in the future convergence of technologies that are reinventing automobile Infotainment and Telematics. HD Radio Advanced Services data transport provides a flexible and addressable digital pipe to the vehicle. Traditionally, local AM/FM radio stations have been the primary source of mobile entertainment and information in the United States. And with the radio industry's conversion to digital broadcasting through the deployment of the Federal Communications Commission (FCC)-approved HD Radio system, terrestrial radio is now a superior method to deliver new and innovative content for local, regional and national telematics services.

The requirement for crew resource management (CRM), or aircrew coordination training (ACT) in military parlance, has been well documented and attested to. In addition, aircraft systems training has become more intense and more in-depth in the new aircraft designs, especially in multi-crew and complex aircraft such as the MV-22 Osprey Tiltrotor. (see Figure 1) Former training systems detailed training procedures that called for classroom training and simulation/simulator training followed by flight training. Improvements in aircraft flight skills training provide increased flying training capability coupled with reduced training time by integrating a mixed simulation/flight training syllabus, e.g. two to three simulation periods followed by one or two flight training periods covering the same material/skills. In addition, the simulation training will introduce new skills; the following flight periods will further refine/hone those skills.

The paper focuses and develops issues raised by the SAE paper ‘THE FUTURE OF VEHICLE ELECTRICAL POWER SYSTEMS AND THEIR IMPACT ON SYSTEM DESIGN’ [1] and describes the realisation of a vehicle with a 12 V architecture of flexible configuration and a power management function. The paper describes the methodology, reasoning and mission behind the creation of the vehicle, developed after collaborative exercises in Europe and the USA, and resulting in a joint programme involving a major vehicle manufacturer and a European system supplier. The electrical system is becoming the focus of activity world-wide due to rapid changes in vehicle requirements, in the areas of safety, environmental and functional demands. There are opportunities for:- (a) Improved starting (b) Integrated management of power generation and demand. (c) Higher system integrity (d) Higher efficiency (e) Improvement of the vehicle electrical environment, giving benefits in component cost.

Five different diesel fuels, having been made available by the mineral oil industry within the framework of a research program of the Coordinating European Council (CEC/PF-26), were examined in addition to this program by the Klöckner-Humboldt-Deutz AG by means of the 13-mode test in accordance with the former US legislation and the ECE regulation No. 49 and by US Transient Tests. The results have been compared with results based on commercial European diesel fuel. There has been observed the emission behaviour of an 8-cylinder NA engine with a “state of the art” direct fuel injection system by particularly taking into consideration the particulate emission and the particulate components. The gaseous emissions, particularly CO and HC, are unfavourably influenced by low cetane numbers being associated with increased aromaticity in the diesel fuel.

In recent years there has been increasing interest in quantifying the emissions from aircraft in order to generate inventories of emissions for climate models, technology and scenario studies, and inventories of emissions for airline fleets typically presented in environmental reports. The preferred method for calculating aircraft engine emissions of NOx, HC, and CO is the proprietary “P3T3” method. This method relies on proprietary airplane and engine performance models along with proprietary engine emissions characterizations. In response and in order to provide a transparent method for calculating aircraft engine emissions non proprietary fuel flow based methods 1,2,3 have been developed. This paper presents derivation, updates, and clarifications of the fuel flow method methodology known as “Fuel Flow Method 2”.

The manner in which the lower deck cargo compartments of standard-body airplanes are designed, equipped, and serviced has not changed appreciably over the past 50 years. A number of factors now at work within the air transportation industry are causing carriers and airplane manufacturers to explore alternative approaches to these tasks. This paper reviews these factors, presents a new approach to lower deck cargo handling systems design, and describes how this approach can be applied to standard-body airplanes.

Carbon and rephosphorized pre-strained sheet steels for cold drawing forming operations were studied and the tensile, high cycle fatigue and fatigue crack propagation properties were determined. The fatigue limit was found to be higher for 20% than for 1% pre-strained condition. Threshold stress intensity factors (▵Ků) of 5.29 MPa. m1/2 for rephosphorized steel and 7.07 MPa. m1/2 for carbon steel. Critical crack lenghts were calculated by ▵Ků and fatigue limit data using the Lukas-Klesnil short-crack criterion. Through fractographic analysis it was possible to determine the general behavior of tested materials near threshold.

The current study has concentrated on discovering and developing clean alternative energy sources like biodiesel and employing novel methods to reduce harmful emissions and enhance engine performance behavior. The consumption of biodiesel in diesel engines reduces the emissions from the tailpipe, but some researchers claim that it actually produces more NOx pollution than engines that run on regular diesel, which limits the use of biodiesel. In this study, Ricinus communis biodiesel was generated through transesterification process, and its fuel properties were assessed. The employ of biodiesel in diesel engines minimize exhaust emissions; however, multiple investigators claim that the consumption of biodiesel generates greater amounts of nitrogen oxide pollutants than diesel-fueled engines, which limits the possibility of biodiesel usage.

Energy demand climbs as a consequence of the inherent relationship between the rate of consumption of energy and the growth of the economy. In light of the depletion of fossil fuels, it is necessary to implement energy efficiency techniques and policies that support sustainable development. Globally, researchers show more interest in discovering fossil fuel alternatives, as a result of fuel crisis. This research elaborates on the production and experimental investigation of briquettes made from ideal municipal solid waste (MSW), such as food waste and garden waste, as a feasible choice for alternate fossil fuels. From Municipal, agricultural, and food waste, we can get biomass waste. Municipal solid and agricultural waste is extensively dispersed, but their potential for converting biomass into energy generation still needs to be explored. This study was carried out based on the information gathered from various studies published in the scientific literature.

Quality assurance (QA) in motor vehicle emissions inspection/maintenance (I/M) programs is a continuing concern, especially in decentralized programs with hundreds or even thousands of licensed stations. The emissions analyzers used in such stations are an important focus of governmental QA efforts because of the central role of analyzers in determining which vehicles need to be repaired. Therefore, the In-use performance of I/M emission analyzers has a large impact on the quality of 1/M programs as a whole. This paper reports on the results of an investigation in California designed to determine in-use performance of emission analyzers in the field. The investigation was designed to evaluate both drift rates and the ability of analyzer systems with automatic gas calibration capability to correct analyzer responses outside of accepted tolerances.

Affordable, efficient and durable catalytic converters for the Commercial Vehicle and Non-Road industry in all countries are required to reduce vehicle emissions under real world driving conditions and fulfill future legal requirements. Specially for India traffic conditions and payload to engine size conditions new cost-effective solutions are needed to participate in a cleaner and healthier environment. Metallic substrates with structured foils like the Transversal StructureTM (TS) or the Longitudinal StructureTM (LS) have been proved to be capable of improving conversion behavior, even with smaller catalyst size. Now Vitesco Technologies is developed a new Substrate for Heavy duty applications that specifically maintains the geometric surface area at a very high level and improves further the mass transport of the pollutants, which potentially leads together to very high pollutant conversion rates.

Due to the rising costs of fuel and increasingly stringent regulations, auto makers are in need of technology to enable more fuel-efficient powertrain technologies to be introduced to the marketplace. Such powertrains must not sacrifice performance, safety or driver comfort. Today's engine and powertrain manufacturers must, therefore, do more with less by achieving acceptable vehicle performance while reducing fuel consumption. One effective method to achieve this is the extreme downsizing of current direct injection spark ignited (DISI) engines through the use of high levels of boosting and cooled exhaust gas recirculation (EGR). Key challenges to highly downsized gasoline engines are retarded combustion to prevent engine knocking and the necessity to operate at air/fuel ratios that are significantly richer than the stoichiometric ratio.

“Digital Prototype” simulations have been used at DaimlerChrysler to achieve vehicle level NVH objectives. The effectiveness of these simulations to guide the design when faced with vehicle parameter uncertainties is discussed. These uncertainties include, but are not limited to, material properties, material gauges, damping, structural geometry, loads, boundary conditions and weld integrity. Manufacturing and assembly processes introduce variations in the nominal values of these parameters resulting in a scatter of vehicle level NVH simulation responses. An example of a high frequency NVH concern will be studied and modified to arrive at robust design guidance when faced with uncertainty. The validity of a “deterministic digital prototype” simulation model and its relevant role as a “trend predictor” rather than “absolute predictor” tool in guiding the design is also discussed.

“DELRIN” is a new thermoplastic which offers high strength, excellent thermal stability, good fatigue life, low creep, and excellent solvent resistance. This paper describes the physical and chemical properties of the material, and the range of possible uses. The material is easily fabricated into complex shapes by standard injection-molding techniques. Also, it can be easily joined to itself or to other materials. The authors think that the material offers advantages over metals in its good fric-tional properties, abrasion resistance, and corrosion resistance.

The Boeing Company in Mesa, Arizona, has been conducting a concept design study of a roadable helicopter called the “Converticar” to assess its feasibility. This is a twin-engine vehicle with twin retractable coaxial counter-rotating rotors. The purpose of the study is to describe a vehicle that carries four passengers in the equivalent of a luxury car that also can fly like a helicopter, and can be priced like a luxury car. To come near this cost goal, the production rate must be on the order of 500,000 units a year. At that rate there is no chance of training a comparable number of pilots each year. So the machine must fly and navigate autonomously, with the pilot just dialing in where he/she wants to go. Technologically, the concept appears to be feasible. Modern design processes, new materials, and improved manufacturing process should allow the Converticar to be built at the prescribed rate when the proper infrastructure for manufacturing it is made available.

A wide body aircraft carries almost a half–ton of water and ice between the cabin and skin of the aircraft. The water can get on wires and connectors, which can cause electrical problems, cause corrosion and rust, and, eventually, “rain in the plane”. The speaker is the CEO of CTT Systems that has developed a system that solves the condensation by using dry air. The speaker will discuss how condensation can be prevented and how airlines can also save maintenance costs in the process. This topic is relevant for the attendees at the Aerospace Expo, as they are decision makers who need to be aware of this issue. It is also important for the MRO shows as the attendees are on the front lines of dealing with this problem.